You need to exert force to loosen and remove the front sight. Below are steps on how to do it. The installation manual is always included in the sight package. It contains the instructions on removing the old sights and replacing them with the new ones. You will be guided on which direction you will apply pressure as you remove the sights. But before you proceed with the process, you need to prepare the tools required to remove and replace the sights.
You can use any screwdriver but make sure it will fit into the tiny set screw found on the rear side. Brass punches do not damage the slide when removing the old sights. The tool may leave a residue. Removed it by using a small drop of oil and a coarse brush. If you prefer steel punches, it may create gouge marks that affect the appearance of your pistol. We suggest using a good brass punch set as it contains plastic punches, which makes it handy.
With regards to hammer, you might be needing not just one type of it. It depends on the strength of your existing sights fixed on the slide. Most of the brass punch set includes the hammer. But in case it does not have, you have to find one. You also need a full-size hammer and a huge rubber mallet if the brass hammer cannot do the job of removing the sights. Put some oil on both sides of the front sight. Let the oil get inside by removing the slide from the vice and setting it on its side.
Get your brass punch and place it on the lip of the front sight, and use the brass hammer to push the sight on the other side. Make sure the vice remains nice and tight while doing the hammering. Once you have removed the front sight, clean the brass marring remaining by the punching process with a wire brush. Before you start the installation process, make sure you have the right front sight for your slide.
It is a safe practice to change the cheaper part. Place the slide in a padded vice, line the vice jaws using a sheet of paper, or mask the slide with tape to prevent the slide from getting marred. With a sanding file or stick, carefully break or reduce the edges of the dovetail on slight and sight. This makes it easy for the sight to start into the dovetail and, at the same time, prevents the dovetail from cutting up the sight while installing. Measure the slide from top to bottom of the cut dovetail, so you will know how much you need to file.
The difference will tell you how much you need to remove without worrying that you might overdo the filing. With a clean and chalked eight-inch file, lay it on the workbench. Hold the front sight between your index finger and thumb.
Slowly pull the sight towards you. Keep the file and sight flat and even. Use a non-marring punch to drive it in place. Be careful on using any tool to make sure it would not mar the sight or the slide with a misaligned tip or hammer blow. The removal of the old sight is the most challenging part of changing it. You need the mentioned tools to complete the job.
You have the option to remove it on your own or let the professionals do it for you. You will be using the same set of tools you used in removing the front sight tool — hammer, brass punch set, and screwdriver. Just like in removing the front sight, you need to exert force to remove the rear sight. Since you will be using the same tools you used in removing the front sight, you already know how to use them. Using the screwdriver, unscrew the rear sight.
The first approach is to get the Milled slide customized. The milling process will allow you to have a rail space for mounting your red dot sight on your handgun. If you want to go the custom route, this process would be for you. This requires time and dedication since you will need to mill your slide and drill some holes into it before attaching the red dot sight. This is a permanent modification for just one optic.
Once the modification is done for a particular red dot sight, it is also an expensive method as compared to the other. The second approach is to mount red dots on your handgun using dovetail sights. To install the dovetail mount, remove your rear iron sights and replace them with a dovetail mount adapter. The process should take about five minutes from start to finish! You can use this method to add a red dot sight to your without making any permanent changes.
It is also the easiest way that requires no modifications to your handgun. If you want to go the quickest route, I recommend buying a red dot-ready handgun. These types of handguns have been optics pre-installed from the factory so that all you need to do is add your optic and start shooting! This option is excellent for those who want to add a red dot sight to their without any hassle. It all depends on your personal preferences and needs. So, be sure to do your research before making a purchase.
So, there you have it! Three different methods for installing a red dot sight on your handgun. Each of these methods has its advantages and disadvantages, so choose the one that best suits your needs. Thanks for reading! You can install a red dot sight on a Colt handgun with three different methods — by customizing the milled slide, using dovetail sights, or buying an optic-ready colt Yes, with the dovetail sight installation method, you can install a red dot sight on a Kimber To install the dovetail optic mount, remove your rear sight and replace it with a dovetail optic mount adapter.
With the dovetail sight installation method, you can install a red dot sight on a Kimber handgun.
0コメント